二维码
业务中心Business
关于我们
业务中心
联系我们
[field:typename/]
你现在的位置:主页 > 业务中心 > 进口业务 >
注塑模具加工时工钱发生的损坏原因都有哪些?
网络整理 [ 浏览点击:] [ 发布时间:2021-02-25 16:52 ]

每个注塑模具加工场都对注塑模具加工时的损坏感想头疼,因为有一些原因完 全可以制止损坏。那么接下来我们公司就为各人浅谈一些注塑模具加工时工钱损坏原因都有哪些?及制止这些损坏息争决方案。

Every injection mold processing factory has a headache about the damage of injection mold processing, because there are some reasons that can completely avoid the damage. Then, our company will talk about the causes of artificial damage in the processing of some injection molds? And avoid these damages and solutions.

注塑面具加工场

Injection mask factory

注塑模具加工中损坏的原因如下:

The reasons for the damage in the processing of injection mold are as follows:

1、全自念头台顶出方法(顶出位置,顶出次数等)调解不妥,产物未脱模合模

1. The ejection mode (ejection position, ejection times, etc.) of automatic machine is not adjusted properly, and the product is not demoulded and closed

注塑模具加工时工资产生的损坏原因都有哪些?

2、全自动产物,产物缺胶顶不出合模压模

2. Fully automatic products, products lack of rubber can not be ejected from the closed die

3、半自动产物,产物未脱模合模压模

3. Semi automatic products, products are not demoulded, combined die

4、监控器报警,没有半自动出产三模,没有查抄模具状况,按全自动出产压模(该种环境,压模频繁)

4, monitor alarm, no semi-automatic production of three models, no inspection of mold conditions, according to the full automatic production of mold (the situation, frequent mold).

5、监控器有图像显示,但未监控或其它原因未监控到位产物不脱模时压模(此种环境压模环境多)

5. The monitor has image display, but it is not monitored or it is not monitored in place for other reasons. When the product is not demoulded, the die is pressed (in this case, the die is often pressed)

注塑模具加工中损坏的办理方案:

The solution of the damage in the processing of injection mold:

1、产物在两次顶出方可顶脱模的,一般设定顶出3-4次。顶出高度设定高于产物高度3MM阁下为适宜

1. If the product can be demoulded only after two times of ejection, it is generally set to ejection 3-4 times. It is appropriate to set the ejection height about 3mm higher than the product height

2、成型调解不妥;机台封胶不良

2. Improper molding adjustment and bad sealing of machine

3、员工事情意识草率大意,龙八国际登录,增强员工培训,培训员工按要求功课

3. The staff work consciousness is careless, strengthens the staff training, trains the staff to operate according to the request

4、让禁锢人员每两小时查抄监控器一次却败监控器有效注塑模具加工

4. Let the supervisor check the monitor every two hours, but the monitor can not effectively process the injection mold

以上就是注塑模具加工时工钱发生的损坏原因和制止这些损坏原因的办理方案。想要相识更多塑胶模具加工的详情资讯,接待存眷:

The above is the reason of artificial damage in injection mold processing and the solution to avoid these damage reasons. For more information about plastic mold processing, please pay attention to:

站点地图

Copyright © 2019 龙八国际工程塑料有限公司 All rights reserved